VMUX-EACU (EXTERNAL ALARM AND CONTROL UNIT) BACK PLANE

EACU (EXTERNAL ALARM AND CONTROL UNIT) BACK PLANE  is designed for monitoring the voltages (AC/DC),temperature, auxiliary inputs and extension of alarms.It can be mounted in standard Sub-rack.The unit can be patched with DAC Card through DAC interface cable.VMUX has an effective Windows based "Network Management System", which may be used for configuring the system,subsequent remote monitoring and management of inter-connected systems in the network.An extensive set of Alarms for easy maintenance is provided in this system.

SALIENT FEATURES

Parameters monitored

-48v source
Ambient Temperature
AC Voltage
8 Auxiliary Inputs

Extends dry loop in case of alarm condition (up to 8)
Powerful Network Management System for monitoring and network control
All configurations stored in non-volatile memory.

VMUX-FRONT PANEL OF DATA ACQUISITION CARD (DAC)

DAC CARD    

                  Front Panel

                        The front panel of DAC Card is shown in figure below:

            The following table describes the front panel:

Item	LED Status	LED Function
HEALTH	Green ON Red    ON BLINKING	Card is working OK. Card hardware has gone faulty.  Card's hardware is OK but it is not configured by main 2mb card

 This card has 8 auxiliary input ports, 8 auxiliary output ports and 6 analog input ports.The analog ports can accept 0-5V input voltage from the various transducers.These transducers units can be used to measure various parameters like temperature, battery Voltage , ac voltage etc.
Installation

·         Slide the card in required slot & lock in position with the help of ejectors.

·         Configure the card and ports using either NMS or NMT , if already not configured.

·         Route the ports, if already not routed.

VMUX-FRONT PANEL OF FRACTIONAL E1 BRANCHING CARD

E1 BRANCHING MODULE CARD           

                 Front Panel

                        The front panel of E1 Branching module card is shown in figure below:

 

                       The following table describes the front panel:

ITEM	LED Status	LED Function
HEALTH	Green ON Blinking	Card is configured. Card is deconfigured.
P1 LCL	ON Fast Blinking Fast Blinking Fast Blinking Slow Blinking Slow Blinking	PCM1 Loss of Signal PCM1 Frame Sync. Loss PCM1 Multiframe Sync. Loss PCM1 CRC Frame Sync. Loss PCM1 error rate > E103 PCM1 error rate > E106
P2 LCL	ON Fast Blinking Fast Blinking Fast Blinking Slow Blinking Slow Blinking	PCM2 Loss of Signal PCM2 Frame Sync. Loss PCM2 Multiframe Sync. Loss PCM2 CRC Frame Sync. Loss PCM2 error rate > E103 PCM2 error rate > E106
P1 RMT	ON Slow Blinking Slow Blinking Slow Blinking	PCM1 Receive AIS (All 1s) PCM1 Receive Remote FSL PCM1 Receive Remote MFSL PCM1 Receive AIS in TS16
P2 RMT	ON Slow Blinking Slow Blinking Slow Blinking	PCM2 Receive AIS (All 1s) PCM2 Receive Remote FSL PCM2 Receive Remote MFSL PCM2 Receive AIS in TS16
CLOCK	Blinking	Slips
TEST	ON	Card in diagnostics or Loop back Mode
TD NMS	Blinking	NMS Polls Transmitted
RD NMS	Blinking	NMS Polls Received

Installation

·         Set the headers for 75 Ω or 120 Ω terminations as per the installation plan.

·         Insert E1 Branching Module card in desired slot & lock it with the help of ejectors.

·         Configure the card and streams using either NMS or Local Port, if already not configured.

                 Route the desired port or streams as require